Fundamental Plumbing Tips for Installing a Bathtub
Fundamental Plumbing Tips for Installing a Bathtub
Blog Article
How do you actually feel when it comes to Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough task. If the old bathtub is easily obtainable, the project can move speedily; if you have to open up a wall to remove the old bathtub as well as position the new bathtub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will require an assistant to vacate the old bathtub as well as embeded in the brand-new one. Ensure you have actually certified on your own for the job and also fit trying it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to take into consideration using one before you begin. Chances are you may require an expert plumber to make tube links.
This post will certainly aid you install a brand-new bath tub in your washroom if you have actually already bought a brand-new bathtub and don't require to alter the arrangement of your previous water supply pipes.
Your tools and product list should consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of removing the existing faucets can be quite problematic because of the limited access that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will come from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines are in place between the tap and also the sink. Secure the faucet in place with the manufacturer given backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bath tub until the spirit level reads degree.
To set up faucets, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the supply of water as well as inspect all joints and new pipework for leakages and tighten them if necessary. Load the bathtub and also examine the overflow electrical outlet and the typical outlet for leaks.
Finally, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bathtub ought to wait till the tub has actually been used a minimum of when as this will certainly resolve it right into its last placement.
Planning for the Setup
Firstly, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a rigid seal, causing the water to penetrate the wall in between the bath and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can split relatively early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very occupied with How to Install a Bathtub Yourself and I am hoping you liked the blog entry. Sharing is good. You never know, you may very well be doing someone a favor. I recognize the value of reading our article about How to Install a Bathtub Yourself.
24-hour service? Dial here. Report this page